คำอธิบาย...
English Description about AEA Ribbon Mics KU5A below
📌 ไมโครโฟนริบบอน Supercardioid รับเสียง Room และ ดึงโทนเสียงเครื่องดนตรีเสียงร้องออกมาแบบธรรมชาติสุดๆ
📌 การออกแบบการรับเสียงรูปแบบซุปเปอร์คาร์ไดออยด์ที่แน่นหนาช่วยให้วางตำแหน่งได้ง่าย
📌 Detailed, extended top end ให้เสียงที่ละเอียดและยาวขึ้น พร้อมโทนของ ribbon smoothness and warmth
📌 มีปุ่ม switch high-pass filter
📌ความทนทานสูงสุดสำหรับการใช้งานในระยะใกล้ กลางแจ้ง และการแสดงสด
📌พื้นผิวสีดำด้านสวยงาม
📌ระบบอิเล็กทรอนิกส์แบบแอคทีฟ(Active)และ custom transformer optimized แบบกำหนดเองที่ปรับให้เหมาะสมสำหรับปรีแอมป์ทั้งหมด
📌ผลิตในประเทศสหรัฐอเมริกา Made in the U.S.A.
KU5A MICROPHONE OVERVIEW
- Supercardioid polar pattern that rejects room tone and instrument bleed
- Detailed, extended top end with ribbon smoothness and warmth
- Supreme durability for close-range, outdoor, and live use
- Active electronics and custom transformer optimized for all preamps
- Front address design with built-in yoke is simple to position
- Integrated high-pass filter switch reduces proximity effect at close-range
- Matte black finish is discreet on camera
- Made in the U.S.A.
THE RIBBON FOR ANY ROOM
The supercardioid KU5A breaks new ground in ribbon technology with its acutely focused directionality that rejects bleed from other instruments, room reflections, and loud ambience in the studio and on stage.
Never before has a ribbon mic delivered as much clarity and breadth of sound in a package so fit for both studio and live use. As a near-field ribbon designed for close range recording, the KU5A delivers the low-end heft and pronounced midrange one expects of AEA ribbons and with moderate, manageable proximity effect. Vocalists can sing directly into the grill of the KU5A, as its interior components are the most protected of any in the AEA lineup.
The KU5A is equipped with active electronics, fit for any preamp in the studio and on the road, as well as an integrated high-pass filter to roll off low end in close range recording applications.
THE SUPERCARDIOID RIBBON
The KU5A’s supercardioid polar pattern captures pure, direct sound while rejecting room tone from behind the mic. This feature prevents excessive monitor and audience bleed when tracking musicians live in one room or on stage. Traditional figure-of-8 ribbons, which distinctly incorporate both direct sound and room sound, rely on sharp Nulls to reject unwanted bleed.
The KU5A’s end-address directionality and tight supercardioid pattern allow for effortless positioning on snare, toms, and other instruments that may be difficult to access. Signal bleed captured by dynamic mics and condensers often sounds harsh and brittle due to top-end frequencies. The minimal bleed captured by the KU5A sounds more natural as a result of its smooth top end and coheres well in a mix.
ACTIVE AND FLEXIBLE
The Active KU5A comes complete with a custom transformer and JFET electronics. It features the same custom transformer as the A440, R84A, and NUVO ribbon mics, providing greater output, less audible noise, and stable impedance. This allows for consistent frequency response and greater flexibility with different preamps, including those within audio interfaces. The boosted output of the KU5A is beneficial when recording quiet sources like vocals and soft acoustic guitars, and the active circuitry prevents noise interference. The KU5A operates with standard 48-volt phantom power.
ROADWORTHY COMPANION
Touring bands rely on the durability and low-profile of the KU5A for sound reinforcement at live shows. At outdoor festivals and indoor theaters alike, the KU5A is perfectly equipped to bring studio sound to the live Stage. Its integrated windscreen protection prevents interference at windy venues and its active electronics allow for flexibility with virtually any mixing board or audio interface.
PECIFICATIONS
Operating Principle: Pressure gradient transducer
Directional Pattern: Supercardioid
Frequency Range: < 20 Hz to >20 kHz
Maximum SPL: 135 dB SPL (1% third harmonic > 1 kHz)
Sensitivity: -43dBv (at 1 kHz, no load)
Output Impedance: 92 Ω broadband
Load Impedance: 1.0 kΩ or greater
Phantom power: Requires 48V Phantom Power, 7mA
Polarity: Pin 2 high for positive pressure at the front of the microphone.
Switchable High-Pass Filter: 6dB/Octave at 283hz
Off Axis Response Relative Output at 180°: – 12dB
Angle of Maximum Rejection: 135°
Transducer Element Material: Pure aluminum corrugated ribbon
Thickness: 1.8 µm
Width: 0.055 in (0.14 cm)
Length: 1.175 in (2.9 cm)
Microphone Dimensions:
Height: 8 in (20.3 cm)
Width: 3 in (7.6 cm)
Weight: 2 lb 9.8 oz (1.19 kg)
Shipping weight: 4 lb (1.8 kg)
Connector: XLR-3M wired to a 3 meter captive cable